November 17, 2026
How to Store Your Pressure Washer Correctly During Perth Winter
By @rowanvcjh007
Storing your pressure washer properly helps protect its pump, hoses and seals while keeping it ready for the next clean. Perth’s winter brings wet weather and damp storage conditions, so moisture control matters even when freezing temperatures are unlikely. Whether you own an electric or petrol machine, a little preparation can prevent corrosion, fuel problems and unnecessary repairs.
Understand Perth’s Winter Storage Conditions
Perth generally has mild winters, but cold nights, rain and condensation can affect equipment stored in open carports or leaky sheds. Coastal suburbs also face salt exposure, which can accelerate corrosion on metal fittings and frames.
Choose a dry, sheltered, well-ventilated storage location. Keep your pressure washer away from wind-driven rain, garden irrigation and areas where water pools. If you live in the Perth Hills or another frost-prone location, take extra care to follow the manufacturer’s cold-weather storage instructions.
Clean and Prepare Your Pressure Washer
- Flush out detergent. Remove or empty the detergent container and flush the detergent system with clean water according to the manual. Do not leave cleaning chemicals sitting in the machine over winter.
- Clean the exterior. Wipe dirt and salt deposits from the housing, frame and fittings. Avoid spraying water into motors, electrical connections, air intakes or engine components.
- Shut down safely. Switch off the machine, unplug electric models and allow petrol engines to cool. Turn off the water supply, then point the gun in a safe direction and squeeze the trigger to release trapped pressure.
- Disconnect and drain accessories. Remove the supply hose, high-pressure hose, gun and lance as directed by the manufacturer. Drain them thoroughly and allow their exteriors to dry before storage.
- Inspect for damage. Check hoses for bulges, cuts or exposed reinforcement, and inspect fittings and seals for leaks. Replace damaged high-pressure hoses rather than patching them.
Do not run the pressure washer dry to empty the pump. Pump-draining procedures vary, and operating without an adequate water supply can cause damage.

Protect the Pump During Longer Storage
Check your owner’s manual for the recommended pump storage procedure. Some manufacturers recommend a compatible pump-protection product during extended storage to help protect internal seals and components. Use only an approved product and apply it exactly as directed.
Do not substitute automotive antifreeze or household chemicals. If freezing conditions are possible, draining accessories alone may not remove water trapped inside the pump. Follow the machine’s specific freeze-protection instructions and store it somewhere protected from frost.
Prepare Electric and Petrol Models Correctly
Electric Pressure Washers
Unplug the machine and check the cable and plug for damage. Store the cord loosely coiled without tight bends, and keep plugs and connections dry and off damp floors. For cordless models, remove the battery and follow its manufacturer’s storage temperature and charge-level guidance.
Petrol Pressure Washers
Petrol can deteriorate during extended storage. Follow the engine manual’s instructions: these may specify adding a suitable fuel stabiliser to fresh fuel or draining the fuel system. Stabiliser does not restore stale petrol.
If the instructions require running treated fuel through the engine, do so outdoors with the pressure washer connected to an adequate water supply. Never run a petrol engine inside a shed or garage. Store fuel only in approved containers, away from ignition sources, and check the engine’s oil and servicing requirements before putting it away.
Store Hoses and Accessories Without Strain
Coil the high-pressure hose in broad loops rather than tight bends. Keep the hose, gun, lance and nozzles clean and supported so their weight does not pull on fittings. Store the machine upright unless its manual specifies otherwise.
A breathable dust cover can help once the equipment is clean, cool and dry. Avoid wrapping a damp machine tightly in plastic, which can trap moisture and encourage corrosion.
Check Before Using It Again
Before your next cleaning job, inspect the water inlet filter, hoses, fittings and electrical lead. Reconnect the water supply and purge air through the gun as directed before starting the machine. Check for leaks and https://housewashingperth.com.au/solar-panel-cleaning/ test the spray on a suitable surface.
If you notice persistent leaks, unusual pump noise or unstable pressure, stop using the washer and arrange an inspection with a Perth pressure washer service technician. A small repair now can help prevent more costly damage later.

House Washing Perth
(08) 7828 5551
❧